ifconfig in short “interface configuration” utility for system/network administration in Unix/Linux operating systems to configure, manage and query network interface parameters via command-line interface or in a system configuration scripts.
[ You might also like: 22 Linux Networking Commands for Sysadmin ]
The “ifconfig” command is used for displaying current network configuration information, setting up an ip address, netmask, or broadcast address to a network interface, creating an alias for the network interface, setting up hardware address, and enable or disable network interfaces.
This article covers “15 Useful “ifconfig” Commands” with their practical examples, which might be very helpful to you in managing and configuring network interfaces in Linux systems.
Update: The networking command ifconfig is deprecated and replaced by the ip command (Learn 10 Examples of IP Command) in most Linux distributions.
[ You might also like: ifconfig vs ip: What’s Difference and Comparing Network Configuration ]
1. View All Network Interface Settings
The “ifconfig” command with no arguments will display all the active interfaces details. The ifconfig command is also used to check the assigned IP address of a server.
[[email protected] ~]# ifconfig eth0 Link encap:Ethernet HWaddr 00:0B:CD:1C:18:5A inet addr:172.16.25.126 Bcast:172.16.25.63 Mask:255.255.255.224 inet6 addr: fe80::20b:cdff:fe1c:185a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2341604 errors:0 dropped:0 overruns:0 frame:0 TX packets:2217673 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:293460932 (279.8 MiB) TX bytes:1042006549 (993.7 MiB) Interrupt:185 Memory:f7fe0000-f7ff0000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:5019066 errors:0 dropped:0 overruns:0 frame:0 TX packets:5019066 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2174522634 (2.0 GiB) TX bytes:2174522634 (2.0 GiB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.1.1.1 P-t-P:10.1.1.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
2. Display Information of All Network Interfaces
The following ifconfig command with the -a argument will display information of all active or inactive network interfaces on the server. It displays the results for eth0, lo, sit0 and tun0.
[[email protected] ~]# ifconfig -a eth0 Link encap:Ethernet HWaddr 00:0B:CD:1C:18:5A inet addr:172.16.25.126 Bcast:172.16.25.63 Mask:255.255.255.224 inet6 addr: fe80::20b:cdff:fe1c:185a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2344927 errors:0 dropped:0 overruns:0 frame:0 TX packets:2220777 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:293839516 (280.2 MiB) TX bytes:1043722206 (995.3 MiB) Interrupt:185 Memory:f7fe0000-f7ff0000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:5022927 errors:0 dropped:0 overruns:0 frame:0 TX packets:5022927 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2175739488 (2.0 GiB) TX bytes:2175739488 (2.0 GiB) sit0 Link encap:IPv6-in-IPv4 NOARP MTU:1480 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.1.1.1 P-t-P:10.1.1.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
3. View Network Settings of Specific Interface
Using interface name (eth0) as an argument with the “ifconfig” command will display details of the specific network interface.
[[email protected] ~]# ifconfig eth0 eth0 Link encap:Ethernet HWaddr 00:0B:CD:1C:18:5A inet addr:172.16.25.126 Bcast:172.16.25.63 Mask:255.255.255.224 inet6 addr: fe80::20b:cdff:fe1c:185a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2345583 errors:0 dropped:0 overruns:0 frame:0 TX packets:2221421 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:293912265 (280.2 MiB) TX bytes:1044100408 (995.7 MiB) Interrupt:185 Memory:f7fe0000-f7ff0000
4. How to Enable a Network Interface
The “up” or “ifup” flag with interface name (eth0) activates a network interface if it is not inactive state and allowing to send and receive information. For example, “ifconfig eth0 up” or “ifup eth0” will activate the eth0 interface.
[[email protected] ~]# ifconfig eth0 up OR [[email protected] ~]# ifup eth0
5. How to Disable a Network Interface
The “down” or “ifdown” flag with interface name (eth0) deactivates the specified network interface. For example, the “ifconfig eth0 down” or “ifdown eth0” command deactivates the eth0 interface if it is in an inactive state.
[[email protected] ~]# ifconfig eth0 down OR [[email protected] ~]# ifdown eth0
6. How to Assign an IP Address to Network Interface
To assign an IP address to a specific interface, use the following command with an interface name (eth0) and ip address that you want to set. For example, “ifconfig eth0 172.16.25.125” will set the IP address to interface eth0.
[[email protected] ~]# ifconfig eth0 172.16.25.125
[ You might also like: How to Configure IP Network with ‘nmtui’ Tool ]
7. How to Assign a Netmask to Network Interface
Using the “ifconfig” command with the “netmask” argument and interface name as (eth0) allows you to define a netmask to a given interface. For example, “ifconfig eth0 netmask 255.255.255.224” will set the network mask to a given interface eth0.
[[email protected] ~]# ifconfig eth0 netmask 255.255.255.224
8. How to Assign a Broadcast to Network Interface
Using the “broadcast” argument with an interface name will set the broadcast address for the given interface. For example, the “ifconfig eth0 broadcast 172.16.25.63” command sets the broadcast address to an interface eth0.
[[email protected] ~]# ifconfig eth0 broadcast 172.16.25.63
9. How to Assign an IP, Netmask, and Broadcast to Network Interface
To assign an IP address, Netmask address, and Broadcast address all at once using the “ifconfig” command with all arguments as given below.
[[email protected] ~]# ifconfig eth0 172.16.25.125 netmask 255.255.255.224 broadcast 172.16.25.63
10. How to Change MTU for a Network Interface
The “mtu” argument sets the maximum transmission unit to an interface. The MTU allows you to set the limit size of packets that are transmitted on an interface. The MTU is able to handle a maximum number of octets to an interface in one single transaction.
For example, “ifconfig eth0 mtu 1000” will set the maximum transmission unit to a given set (i.e. 1000). Not all network interfaces support MTU settings.
[[email protected] ~]# ifconfig eth0 mtu 1000
11. How to Enable Promiscuous Mode
What happens in normal mode, when a packet is received by a network card, it verifies that it belongs to itself. If not, it drops the packet normally, but in the promiscuous mode is used to accept all the packets that flow through the network card.
Today’s network tools use the promiscuous mode to capture and analyze the packets that flow through the network interface. To set the promiscuous mode, use the following command.
[[email protected] ~]# ifconfig eth0 promisc
12. How to Disable Promiscuous Mode
To disable promiscuous mode, use the “-promisc” switch that drops back the network interface in normal mode.
[[email protected] ~]# ifconfig eth0 -promisc
13. How to Add New Alias to Network Interface
The ifconfig utility allows you to configure additional network interfaces using the alias feature. To add the alias network interface of eth0, use the following command. Please note that the alias network address is in the same subnet mask. For example, if your eth0 network ip address is 172.16.25.125, then the alias ip address must be 172.16.25.127.
[[email protected] ~]# ifconfig eth0:0 172.16.25.127
Next, verify the newly created alias network interface address, by using the “ifconfig eth0:0” command.
[[email protected] ~]# ifconfig eth0:0 eth0:0 Link encap:Ethernet HWaddr 00:01:6C:99:14:68 inet addr:172.16.25.123 Bcast:172.16.25.63 Mask:255.255.255.240 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:17
14. How to Remove Alias to Network Interface
If you no longer required an alias network interface or you incorrectly configured it, you can remove it by using the following command.
[[email protected] ~]# ifconfig eth0:0 down
15. How to Change the MAC address of Network Interface
To change the MAC (Media Access Control) address of an eth0 network interface, use the following command with the argument “hw ether“. For example, see below.
[[email protected] ~]# ifconfig eth0 hw ether AA:BB:CC:DD:EE:FF
These are the most useful commands for configuring network interfaces in Linux, for more information and usage of the ifconfig command use the manpages like “man ifconfig” at the terminal. Check out some other networking utilities below.
Other Networking Utilities
- nmcli – a command-line client that is used to control NetworkManager and report network information.
- Tcmpdump – is a command-line packet capture and analyzer tool for monitoring network traffic.
- Netstat – is an open-source command-line network monitoring tool that monitors incoming and outgoing network packets traffic.
- ss (socket statistics) – a tool that prints network socket-related information on a Linux system.
- Wireshark – is an open-source network protocol analyzer that is used to troubleshoot network-related issues.
- Munin – is a web-based network and system monitoring application that is used to display results in graphs using rrdtool.
- Cacti – is a complete web-based monitoring and graphing application for network monitoring.
To get more information and options for any of the above tools, see the man pages by entering “man toolname” at the command prompt. For example, to get the information for the “netstat” tool, use the command “man netstat“.